Buz/hum active speaker with new turntable

[freddyonderstal]

This afternoon I installed my new turntable, a Thorens TD 403 DD. My active speakers are the floor-standing Argon Audio Fenris A55.

The speakers have a built-in amplifier; the turntable is connected to the Phono input via an RCA cable.

If the turntable is off and I only have the speakers on, I hear a soft hum/buzz when I turn the volume up to halfway. Below that, it is barely audible, if at all. Again: the turntable is off but connected, and I have also connected the ground cable between the speaker and the turntable.

Is this normal? How can I fix this?
Can this do any harm to my new turntable?

 

[Gray]

Can this do any harm to my new turntable?

No, but you don't want any hum or buzz from the speakers.
What did you have / do you still have feeding the speakers (apart from the turntable)?

 

[Al ears]

What happens if you disconnect the earth cable?
How have you managed to connect the turntable, with its short cables to those speakers?

 

[freddyonderstal]

No, but you don't want any hum or buzz from the speakers.
What did you have / do you still have feeding the speakers (apart from the turntable)?

Only the turntable is connected to the speaker.

 

[freddyonderstal]

What happens if you disconnect the earth cable?

The buzz gets louder/very loud.

 

[Shrek]

how close are the speakers to the turntable ?

 

[freddyonderstal]

how close are the speakers to the turntable ?

The left speaker, where the amplifier is in, is about 20cm’s away from the TT. The right speaker is about 1 meter away.

 

[Shrek]

The left speaker, where the amplifier is in, is about 20cm’s away from the TT. The right speaker is about 1 meter away.

having the speakers to close to the TT will not help try moving the left speaker further away see if that helps .

 

[freddyonderstal]

having the speakers to close to the TT will not help try moving the left speaker further away see if that helps .

I’ll try that. But is it possible to hear the buz when the turntable is off, like it is now?

 

[Gray]

Only the turntable is connected to the speaker.

Turn the speakers volume to minimum.
Disconnect both RCA signal plugs from the turntable.
With the speaker end of the twin RCA cable still plugged into the phono input:

Put a direct short circuit across both left and right open ended RCA plugs (between the central pin and outer plug body).
Then turn the speaker volume up.
You should have silence at the halfway point.
See whether you have.

 

[freddyonderstal]

Tried something;

On the back of the active speaker is a volume knob. It was at 8 o’clock. When I raise the volume with the remote control, I could go 3 presses up before the buzz is becoming hearable.

I turned the knob on the back of the speaker on 12 o’clock, the buz becomes hearable after 7 presses on the remote control.

Can anyone explain how this is possible? The volume knob at the back of the speaker is normal output volume, right?

 

[Gray]

Tried something;

On the back of the active speaker is a volume knob. It was at 8 o’clock. When I raise the volume with the remote control, I could go 3 presses up before the buzz is becoming hearable.

I turned the knob on the back of the speaker on 12 o’clock, the buz becomes hearable after 7 presses on the remote control.

Can anyone explain how this is possible? The volume knob at the back of the speaker is normal output volume, right?

Remote and physical volume control effectively do the same thing.
You're going off at a tangent.
Some speakers with built-in amps have undesirable, inherent background noise.
You need to know whether yours are sufficiently quiet - before questioning anything connected to them.